Have you been looking for suggestions about How to Install a Bathtub?
Mounting a bathtub isn't exactly brain surgery, yet it does call for strong plumbing, carpentry, and often, tiling abilities. Replacing an old tub with a brand-new one is also a moderately tough task. If the old tub is easily obtainable, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub as well as place the brand-new tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly need a helper to leave the old bathtub and embeded in the brand-new one. Make sure you have certified on your own for the job as well as fit attempting it. Instead of employing a contractor to take over a halfway-completed job, it is much better to take into consideration using one before you begin. Opportunities are you might need a professional plumber to make tube links.
This write-up will certainly help you set up a brand-new bath tub in your washroom if you have already gotten a brand-new tub and also don't need to alter the plan of your previous water pipelines.
Your tools and material checklist must consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, switch on the taps to drain any type of water staying in the system. The procedure of eliminating the existing faucets can be fairly bothersome as a result of the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing compound.
Before moving on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin guaranteeing that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the manufacturer offered backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical tap ports. The former kind ought to be connected to the faucet ends initially, tightening just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Utilizing the two wood boards under its feet, place the bath tub in the required placement. The wooden boards are handy in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the spirit level as well as readjusting the feet on the tub till the spirit level reviews level.
To set up taps, fit the bottom of the outermost flexible faucet connector to the proper supply pipe by making a compression join; after that do the same for the various other faucet.
Turn on the water and inspect all joints and also new pipework for leakages and tighten them if required. Load the bathtub and additionally check the overflow electrical outlet and also the normal electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's user's manual. Tiling and also sealing around the tub needs to wait until the tub has actually been made use of at least once as this will certainly resolve it into its final setting.
Planning for the Installation
First of all, the sustaining structure supplied with the bath must be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to stop pressure on the bathtub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you utilize every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to split a stiff seal, triggering the water to permeate the wall between the bathroom as well as the tiling, leading to issues with moisture as well as possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes and cartridges, as well as are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to always load the bath tub with water before sealing, to permit the motion experienced when the tub remains in usage. The sealant can fracture rather early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water-proof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that page about Installing A Bathtub when browsing the internet. Do you know somebody who is interested in the subject? Please feel free to promote it. Thanks for going through it.
Detail